Pyroshock Testing – Delserro Engineering Solutions https://www.desolutions.com/blog Product Reliability & Vibration Testing Since 1982 Fri, 22 Jan 2016 19:35:32 +0000 en-US hourly 1 https://wordpress.org/?v=5.6.13 What is Pyroshock Testing? https://www.desolutions.com/blog/2014/05/what-is-pyroshock-testing/ https://www.desolutions.com/blog/2014/05/what-is-pyroshock-testing/#respond Tue, 13 May 2014 13:37:11 +0000 https://www.desolutions.com/blog/?p=2019 First we should answer, what is a pyroshock or a pyrotechnic shock? Both pyroshocks and pyrotechnic shocks are the same thing. A pyroshock occurs when explosive events are used to separate the stages of rockets or missiles, or from a ballistic impact to a structure by a projectile. When a pyroshock occurs, a stress or …

Continue reading What is Pyroshock Testing?

The post What is Pyroshock Testing? appeared first on Delserro Engineering Solutions.

]]>
First we should answer, what is a pyroshock or a pyrotechnic shock? Both pyroshocks and pyrotechnic shocks are the same thing. A pyroshock occurs when explosive events are used to separate the stages of rockets or missiles, or from a ballistic impact to a structure by a projectile. When a pyroshock occurs, a stress or shock wave propagates through the structure and into the electronic equipment contained within the structure.

Pyroshocks are unique shocks that have high G-level, high frequency content with very little velocity and displacement change during the shock. The frequency range of a pyroshock is usually 100 Hz to 10,000 Hz or greater. Pyroshocks have a very short duration of usually less than 20 milliseconds. The acceleration time history of a pyroshock approximates a combination of decaying sinusoids as shown in Figure 1.

Pyroshock Acceleration Time History
Figure 1. Acceleration Time History of a Pyroshock Performed at DES.

Pyroshock rarely causes failures in structural members. Typical failures include mechanical relay or crystal oscillator chatter, failures of small circuit board components and dislodging of solder balls which cause short circuits.

The following definitions are from MIL-STD-810G, Method 517, but vary among different pyroshock standards.

Near-field Pyroshock: Maximum frequencies greater than 10,000 Hz and peak amplitudes greater than 10,000 G’s.

Mid-field Pyroshock: Maximum frequencies between 3,000 Hz to 10,000 Hz and peak amplitudes less than 10,000 G’s.

Far-field Pyroshock: Maximum frequencies less than 3,000 Hz and peak amplitudes less than 1,000 G’s.

There is a lack of analytical techniques available to predict a product’s response to a pyroshock. Thus manufacturers must rely on pyroshock testing to qualify their products. Pyroshock testing can be performed using explosive charges or by high energy short duration mechanical impacts. DES uses a Mechanical Impulse Pyroshock Simulator (MIPS) shown in Figure 2 to perform most pyroshock testing. However far-field pyroshock is sometimes completed on our electro-dynamic shakers. DES’s pyroshock equipment capabilities include:

  • Mid-field pyroshock with Mechanical Impulse Pyroshock Simulator (MIPS)
  • Far-field pyroshock with Electro-Dynamic Shaker or MIPS Simulator
  • Frequency control up to 10,000 Hz
  • Shock Response Spectrum (SRS) analysis
  • Modern high speed sigma-delta data acquisition with numerous channels
MIPS Table
Figure 2. DES’s MIPS Table.

Shock Response Spectrum (SRS) analysis is used to measure the acceleration as a function of frequency and the total energy of the applied shock pulse. The SRS is a curve that represents the response of many damped single degree-of-freedom oscillators to a shock pulse. The damped oscillators are tuned to specific octave or frequency bands. A SRS analysis of a pyroshock completed by DES is shown in Figure 3.

SRS Analysis of a Pyroshock
Figure 3. SRS Analysis of Pyroshock by DES.

DES has successfully performed pyroshock tests on many electronic products that are used in outer space, rockets, and missiles. DES MIPS table has many adjustments to allow for repeatability and shaping of the shock pulses. It is also grounded for ESD sensitive products. Some size and weight ranges for products that we have tested include:

  • Size range from less than a 2” x 2” footprint to greater than a 25” x 20” footprint
  • Weight range from ounces to 50 pounds

To watch a pyroshock test be performed on our MIPS table, visit our YouTube channel.

Our experienced engineers understand the need for proper selection of the accelerometers along with the setup of the high speed data acquisition system. We have performed an anti-aliasing study on our data acquisition system to prove that it is capable of the demanding requirements for pyroshock measurements without aliasing. This study is available upon request. Please contact DES to learn more about our pyroshock testing and other shock testing capabilities.

The post What is Pyroshock Testing? appeared first on Delserro Engineering Solutions.

]]>
https://www.desolutions.com/blog/2014/05/what-is-pyroshock-testing/feed/ 0